€295.00 + VAT

Insulation Resistance Tester MG500
[MG500]

Insulation Resistance Tester MG500

Allows you to measure insulation resistance more safely by avoiding operation mistakes!!

Hot-line state detection
In any range (MΩ), the hot-line state (30 V minimum) can be detected through the buzzer sound and the red LED illumination. If you press the MEASURE button by mistake in this state, no test voltage will be generated. Thus, the measuring circuit and the equipment involved will not be affected adversely.

Large bolt mark
During the measurement of MΩ, a large bolt mark is illuminated on the LCD with the buzzer sound, allowing you to find that voltage is generated.

More ingenuity
To select the highest test voltage range, you need to turn the rotary switch while holding down the 0Ω ADJ button. This design feature prevents the highest test voltage from being generated by an operation mistake.

Easy to use & tough body
An easy-to-hold body with a portrait design has been adopted to ensure stable measurements. The tester comes with a strap, and uses less slippery elastomeric material for its lateral sides so that the user can grip the tester more firmly.

Automatic data hold
After measurements have been finished, the last measured value can be held automatically. Unlike an analog tester, you do not need to check the reading during measurements and therefore can comfortably concentrate on the object under measurement.

Bargraph just like analog meter
A large logarithmic bar graph is provided to enable the user to check the measured value like using an analog tester.

Large display with backlight
The backlight allows you to check the measured value even in a dark place. Since the rated voltage output can be checked with the green LED, you can find whether the measurement is being carried out properly.

General Specification

MG500 


Reviews
Manufacturers
1 x Crosscut 'Super-Cut' blade
1 x Delta sander OZI/E
1 x Precision steel vice PM 40
1 x Side cutters 195mm
2 x 
1 x Super safety and specialty bit set, 75-piece
1 x Microfibre cloth
2 x Edge cutter with pin 6.4mm
1 x Polishing Set
2 x Brass contact cleaner brush
1 x Bench drill press TBH
1 x Tungsten tipped saw blade
1 x Diamond-coated cutting and roughing disc
2 x Diamond-coated cutting disc for MIC
1 x surface planing and thicknessing ADH 200
1 x Belt sander BBS/S
1 x sandpaper for PS 13 Grit 400
2 x Independent four jaw chuck for the DB 250
1 x Band knife of hardened spring band steel (without teeth)
2 x Slot cutter 3.2mm
1 x Precision caliper 500mm
1 x Grinding mop cylinder grit 80
2 x Core box bit 3.2mm
3 x HSS boring tool set, 6 pieces
1 x PLCC Puller
3 x Three piece thread cutting set
1 x Milling cutter set (6 - 10mm)
2 x TORQUE-SCREWDRIVER 1.5 - 4.0 Nm
2 x TORQUE-SCREWDRIVER 0.5 - 1.5 Nm
1 x replacement glass fibre for 2-166 Ø 4mm (PU 10)
1 x Glass fibre contact cleaner brush
1 x Glass fibre contact cleaner brush
1 x Milling cutter set (2 - 5mm)
1 x Half round cutter 13mm
1 x Coarse-toothed (10 TPI per 25mm)
1 x Rasp plate with metal burrs made from wolfram carbide for LWS
2 x Lathe System PD 400
1 x Compact workshop vacuum cleaner CW-matic
1 x Round nose pliers 45º EUROline-Conductive
1 x 14-piece parallel supports set
1 x TU 2404
1 x Fluted filter for CW-matic
1 x Cone shaped milling cutter
1 x MICROFLAM gas soldering set MGS
1 x Telephone pliers straight 205mm
1 x Snipe nose pliers 45º EUROline-Conductive
1 x Gear Chuck
1 x Snipe nose pliers 45º EUROline-Conductive
1 x Flap Wheels
1 x MICRO-screwdrivers
1 x Flexishaft MICROMOT 110/P
1 x Solid carbide stylus for engraving
1 x Grinding mop cylinder grit 120
1 x Tungsten carbide cutter 3.0mm
1 x Cutting tools of high quality cobalt HSS steel, ground
1 x Side cutters 160mm
1 x Mini side cutters EUROline-Conductive
1 x Diamond Grinding Bits 1,8mm
1 x Coarse-toothed (25 TPI per 25mm)
1 x Ball-shaped diamond coated 2.2mm
1 x Cutting tools of high quality cobalt HSS steel, ground
1 x Fine dust paper filter for CW-matic
1 x Belt sander BS/E
1 x MICRO Screwdriver MIS 1. Complete with 16 inserts.
1 x Ball-shaped diamond coated 3.2mm
1 x Coarse-toothed blades (No. 5: 17 teeth per 25mm)
1 x Round nose pliers 165mm
1 x Universal holder UHZ
1 x Cylinder shaped milling cutters
1 x Bench drill machine TBM 220
1 x High quality corundum grinding bits
€9,366.39
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
We Accept
Manufacturer Info
SANWA-METER
SANWA-METER Homepage
Other products
Languages
Portugues English
Share Product
Share on Facebook